الحلول االسمنتية صنع في األردن حسب مواصفات أمريكية و أوروبية. Made in Jordan according to American and European specifications.

Transcription

1 Made in Jordan according to American and European specifications صنع في األردن حسب مواصفات أمريكية و أوروبية الحلول االسمنتية Contact Us: Tel: ( ) Mob: ( ) petrajo@orange.jo

2 CEMENT SOLUTIONS: WHO WE ARE: We are Petra Chemicals Co., producers of wide range of construction chemicals under the brand name CEMENTSOLUTIONS, our factory is located at Abu Alanda Industrial Zone, Amman, Jordan, with a production capacity up to 120 tons per day. Our products comply with the American and European standards according to certified tests, with a very competitive prices. SCOPE OF PRODUCTS: Tile Adhesive & Grout, Concrete Repair, Non-Shrink Grouts, Surface Treatments, Bonding Agents, Flooring & Coatings, Waterproofing, decorative finishing, and many other products for special purposes. FOR MORE INFORMATION ABOUT OUR PRODUCTS PLEASE CHECK THE DRAWING: Which would help you better understand our products, solutions for variety of cases, application tips and products recommendations to utilize and improve your project quality. CONTACT US: Tel: ( ) Mob: ( ) petrajo@orange.jo

3

4 Exterior Paints: For More Information Please Click The. Exterior Paints has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the exterior paint after the Surface Preparation is accomplished we suggest the CEMEPROOF PAINT it has been formulated to confer long term protective and decorative properties to concrete and masonry surfaces.

5 Exterior Paints: CEMEPROOF PAINT Elastomeric acrylic emulsion, waterproofing anti-carbonation and weatherproofing UVresistant coating for exterior applications. Packaging CEMEPROOF PAINT Weatherproofing and anti-carbonation Paint for outdoor use. 5 Kg or 20 Kg. microns thickness per plaster. White or Light Grey (BS4800 or RAL colors are available upon request). Apply coating by brush, roller or airless spray at a nominal rate of 5m²/liter and allow to dry, A second coat may be subsequently applied at the same rate. Back to Exterior Paints

6 Roof Waterproofing: For More Information Please Click The. Roof Waterproofing has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the roof waterproofing after the Surface Preparation is accomplished we suggest 2 systems: 1. Acrylic System: First step use CEMECRYL PRIMER which is liquid admixture to improve bonding, and workability of the surface. The second and last step use CEMELASTIC which is a waterproof elastic single component coating for all types of roofs. 2. Cementitious System: First step use CEMECRYL PRIMER which is liquid admixture to improve bonding, and workability of the surface. Then use CEMELEVEL POLYMER UW which provides a non-toxic, waterproofing and floor over lay for releveling and refurbishing cementitious based floor slabs. Last step use CEMEFLOOR GLAZE which is transparent polymer sealer, gloss finish, for protection of concrete, and zero absorption surface.

7 Roof Waterproofing: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Porosity sealer and primer applied directly on the surface. Packaging 5 L 25 L. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

8 Roof Waterproofing: 2. CEMELASTIC is an elastic acrylic coating, specially formulated for all types of roofs. It is supplied in the form of a water-based single component paint, ready to use. Once polymerized it is transformed into an UV-rays resistant and waterproofing film. Packaging CEMELASTIC Waterproofing, flexible and resistant to sun rays and non-preamble to water for roof application. 5 Kg or 20 Kg. 1 Kg covers 2 1 mm surface. White or Grey (BS4800 or RAL colors are available upon request). Applied by brush or roller. When using an airless spray, dilute with a sufficient but minimum amount of water to allow the easy application of the product, 2 coats recommended. Back to Roof Waterproofing Previous

9 Roof Waterproofing: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Porosity sealer and primer applied directly on the surface. Packaging 5 L 25 L. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

10 Roof Waterproofing: 2. CEMELEVEL POLYMER UW is a self-level cementitious two-component product. Component A is a mortar based on a special polymerized mixture, and component B is a water-based special acrylic resin. It provides a non-toxic, waterproofing and floor over lay for releveling and refurbishing cementitious based floor slabs. CEMELEVEL POLYMER UW Packaging (A) 20 Kg + (B) 5 L. Waterproofing, flexible and resistant to sun rays and non-preamble to water for roof application. 1 package covers 1 mm smooth surface. Grey (Concrete Color). Pour or pump the mixed material onto the surface spread with trowel and allow to level, and allow attaining a smooth finish, it can be diluted with CEMECRYL PRIMER for high temperature to give better workability. Previous Next

11 Roof Waterproofing: 3. CEMEFLOOR GLAZE is a transparent polymer sealer, derived from methacrylate-based resins. It forms a durable, tough and flexible film with gloss finish for protection of concrete and masonry. It resists weathering, air pollutants, alkaline agents and ultra-violet rays (UV). CEMEFLOOR GLAZE Packaging 5 L or 25 L. Clear acrylic developed to provide hard, glossy, Protective Sealer to beautify and protect regular concrete surface. 1 L Covers microns thickness per smooth surface. None. Apply with brush, roller, or spray, 2 coats recommended. Back to Roof Waterproofing Previous

12 Repair Materials: For More Information Please Click The. Repair Materials works usually for so many factors that achieve the best repair, repair materials products have advantages in all factors to satisfy the project needs, such as high adhesion strength to older concrete, nonshrinkage materials, high mechanical properties and easy to use and apply after surface preparation is accomplished. 1. CEMEBUTTY FC200 Cementitious thin fairing putty repair mortar for concrete surfaces, plaster surfaces, and fair face repair. 2. CEMEPATCH XTRA Repair mortar enhanced with fibers, special cements, additives and selected aggregates. 3. SHOTCRETE F20 Repair cement mortar for buildings and large areas repair. 4. CEMEPATCH 400 Structural component with a thixotropic product and shrinkage-compensated for repairs. 5. CEMECRYL JOINT SEALANT Joint acrylic sealant and crack filler. 6. CEMECUR 101 Concrete curing agent to prevent an excessive fast drying. 7. CEMEHARD 100 Dry-Shake cement hardener powder for concrete surfaces hardening. 8. CEMECLEANER Polishing, shining, and cleaning. 9. CEMEFLOW G100 non-shrinkage grout for under-machinery and steel plates uses. 10. CEMEBOND LATEX SBR additive and bonding agent to cement to improve mechanical properties and water retention.

13 Repair Materials: 1. CEMEBUTTY FC200 is a one part, polymer modified, cementitious thin fairing putty repair mortar for concrete surfaces, and plaster surfaces. Needs adding water for application. Packaging CEMEBUTTY FC200 Cover minor surface defects on concrete, plaster, mortar and stone masonry, It is suitable for small repairs, and fair face concrete surfaces. 20 Kg. Depends on the repair size. Light Grey. Mix each 20 Kg with 4-5 L of water then apply on the prepared surface using a steel trowel. It should be worked well into the pin holes and surface blemishes. It should be allowed to set partially before final finishing with sponge or steel trowel. Water can be sprinkled on the applied material before final trowel or sponging. Back to Repair Materials

14 Repair Materials: 2. CEMEPATCH XTRA Structural repair mortar enhanced with fibers, special cements, additives and selected aggregates. Needs adding water for application. Packaging CEMEPATCH XTRA Cover major surface defects on concrete, plaster, mortar and stone masonry,, It is suitable for big repairs, and voids in concrete. 25 Kg. Depends on the repair size. Grey (Concrete Color). Mix 25 Kg with 5 L of water then apply on the repair spot using a steel trowel. It should be allowed to set partially before final finishing with sponge or steel trowel. Water can be sprinkled on the applied material before final trowel or sponging. Back to Repair Materials

15 Repair Materials: 3. SHOTCRETE F20 is made with accurately mass-batched blends of Portland cement, polymers, sand, course aggregate and powdered accelerator. It has been specifically designed for applications that require fast setting characteristics used in mining, tunneling and civil projects. Packaging SHOTCRETE F20 Dry bagged shotcretes are used in a wide range of civil engineering and mining applications, where fast drying and vertical ceiling application take place. 25 Kg. Depends on the surface. Grey (Concrete Color). Mix 25 Kg with 6 L of water apply on the prepared surface using a steel trowel, or spray gun. Water can be sprinkled on the applied material before final trowel or sponging. Back to Repair Materials

16 Repair Materials: 4. CEMEPATCH 400 is one-component structural repair mortar, composed of special cements, additives and selected aggregates, which provides a thixotropic product with quick-setting and shrinkage-compensated. Meets Class R4 according to European Standard EN CEMEPATCH 400 Packaging Restoration of structural concrete elements, recovering original shape and function. 25 Kg. Depends on the surface. Grey (Concrete Color). Applied on the prepared surface using a steel trowel. It should be allowed to set partially before final finishing with sponge or steel trowel. Water can be sprinkled on the applied material before final trowel or sponging. Back to Repair Materials

17 Repair Materials: 5. CEMECRYL JOINT SEALANT is a water-based single component acrylic paste, stops the flow of water to permanently repaired concrete cracks, holes and joints, it maintains flexibility and water proofing joint sealant and provides outstanding durability. Packaging CEMECRYL JOINT SEALANT Maintenance of joints in concrete, concrete runway and crack repair in concrete. 1 Kg or 5 Kg. Depends on the surface. Light Grey. Can be applied a manually or with gun. Use typical joint sealing practices and proper joint design of 2:1 width to depth ratio when applying. Horizontal joints require a minimum of (15 mm) depth and maximum (30 mm) depth. After application the product can be smoothed with a polish. Back to Repair Materials

18 Repair Materials: 6. CEMECUR 101 is a water-based milky pure acrylic resin, a curing agent that sprayed over the surface of fresh concrete or mortar, provides a thin film acting as a protective barrier to prevent an excessive fast drying. CEMECUR 101 Curing of fresh concrete and mortar. Packaging 25 L or 200 L. 1 L covers 4 m2. None. Can be sprayed by either manual or air-powered spray, directly over the surface of fresh concrete or mortar, leaving a thin and continuous film. The application will be carried out in two successive coats, being sprayed when the surface has started to become matt Back to Repair Materials

19 Repair Materials: 7. CEMEHARD 100 is formulated with special cements, pigments, additives and aggregates designed to be applied on fresh concrete in order to improve its abrasion resistance and provides an anti-dust finish in one single application. CEMEHARD 100 Packaging Harding of pavements of garages, parking, shopping malls, schools, hospitals. 25 Kg. 3 Kg covers 1 m2. Grey (Concrete Color) (BS4800 or RAL colors are available upon request). The concrete slab should be perfectly extended, lined and leveled. The concrete will be designed with enough structural resistance for the required purpose. Back to Repair Materials

20 Repair Materials: 8. CEMECLEANER is designed for cleaning salts, grease and oil on cement and concrete surfaces. It s special formulation attacks and dissolves the stains helping to eliminate them. Packaging 5 L. CEMECLEANER Cleaning agent for oils, animal grease, etc., on cement and concrete floors, pavements and walls. Depends on the surface and the dissolves. None. Spill over stains and let it react for minutes then brush and once the remains of the stain have disappeared, wash thoroughly with clean water and allow it to dry Back to Repair Materials

21 Repair Materials: 9. CEMEFLOW G100 is an one-component non-shrink mortar formulated from special cements and wellgraded mineral products which provides high mechanical properties and fluidity vibration resistance. Packaging CEMEFLOW G100 Base concrete of machines and grid beams. 25 Kg. Depends on depth and thickness. Grey (Concrete Color). Mix with 5 L of water apply simply pouring by gravity directly from the mixing container. In order to avoid cold joints and minimize the chance of air entrapment. Back to Repair Materials

22 Repair Materials: 10. CEMEBOND LATEX SBR is a water-based styrene-butadiene liquid admixture for mixing of bonding slurries and improvement of physical properties for mortars and concretes. Packaging 5 L or 25 L. CEMEBOND LATEX SBR As a Prime or bonding agent. Between old and fresh mortars. Can be added to cement mix for better properties. 1 L covers 5m2 (as a prime). 2 L for each cement bag (in mix). None. On porous substrates and/or with different grades of absorption, in order to provide a homogeneous surface, apply one coat of pure CEMEBOND LATEX by brush, broom or roller leaving no puddles. Or mix directly with cement mixes. Back to Repair Materials

23 Concrete Water Tanks Waterproofing: For More Information Please Click The. Concrete Water Tanks Waterproofing has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the concrete water tanks waterproofing after the Surface Preparation is accomplished we suggest to waterproof the tanks from inside and outside: Inside Concrete Tank or Well: 1. CEMECRYL PRIMER is liquid admixture to improve bonding, workability and curing of mortar and concrete. 2. CEMESEAL FLEX is a waterproofing coat for water wells and swimming pools. 3. CEMEFLOOR SF400 Epoxy floor coating system designed for protection of concrete floors. Outside Concrete Tank or Well: 4. BITUPRIME EL-10 Cold rubberized bitumen emulsion for underground foundations and walls waterproofing.

24 Concrete Water Tanks Waterproofing: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Packaging 5 L or 25 L. Porosity sealer and primer applied directly on the surface. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

25 Concrete Water Tanks Waterproofing: 2. CEMESEAL FLEX is a cementitious acrylic two-component product that provides a non-toxic, flexible and waterproof coating with very high adhesion on those common substrates in construction such as concrete and masonry. CEMESEAL FLEX Packaging (A) 18 Kg + (B) 5 L. Waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools. Package Covers micron thickness. Grey (Concrete Color). Mix with electrical mixer then apply it using a short, stiff bristle brush or roller. Previous Next

26 Concrete Water Tanks Waterproofing: 3. CEMEFLOOR SF400 is a solvent free, two components high build colored system consisting of Epoxy resin and polyamine curing agent. It is designed to provide shameless concrete surface resistance to abrasion and protect against chemical attack. Packaging CEMEFLOOR SF400 High performance epoxy coating with excellent decorative finishing in water tanks, shopping centers, flooring warehouses, floors and walls, and car parking. (A) 4.9 Kg + (B) Kg Package covers micron smooth surface. Standard colors (BS4800 or RAL colors are available on request). Mix (A) with (B) using low speed mixer then apply using short hair roller. Previous Next

27 Concrete Water Tanks Waterproofing: 4. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing. BITUPRIME EL-10 Packaging 5 L or 18 L or 200 L. 1 L Covers 3 m2. s from building foundations to bridge abutments, retaining walls, flower boxes, box gutters or any other area where water must be kept in or out. Brown. Mix with electric mixer for minutes then apply easily and inexpensively by unskilled personnel. No special equipment is required as application is by normal brushes, or rollers. Back to Tanks Waterproofing Previous

28 Podium Waterproofing: For More Information Please Click The. Podium Waterproofing has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the podium waterproofing after the Surface Preparation is accomplished we suggest to waterproof the Podium from inside and outside: Inside Podium: 1. CEMECRYL PRIMER is liquid admixture to improve bonding, workability and curing of mortar and concrete. 2. CEMESEAL FLEX is a waterproofing coat for water wells and swimming pools. Outside Podium: 3. BITUPRIME EL-10 Cold rubberized bitumen emulsion for underground foundations and walls waterproofing.

29 Podium Waterproofing: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Packaging 5 L or 25 L. Porosity sealer and primer applied directly on the surface. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

30 Podium Waterproofing: 2. CEMESEAL FLEX is a cementitious acrylic two-component product that provides a non-toxic, flexible and waterproof coating with very high adhesion on those common substrates in construction such as concrete and masonry. CEMESEAL FLEX Packaging (A) 18 Kg + (B) 5 L. Waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools. Package Covers micron thickness. Grey (Concrete Color). Mix with electrical mixer then apply it using a short, stiff bristle brush or roller. Previous Next

31 Podium Waterproofing: 3. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing. BITUPRIME EL-10 Packaging 5 L or 18 L or 200 L. 1 L Covers 3 m2. s from building foundations to bridge abutments, retaining walls, flower boxes, box gutters or any other area where water must be kept in or out. Brown. Mix with electric mixer for minutes then apply easily and inexpensively by unskilled personnel. No special equipment is required as application is by normal brushes, or rollers. Back to Podium Waterproofing Previous

32 Decorative Plaster: For More Information Please Click The. Decorative Plaster has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the decorative plaster after the Surface Preparation is accomplished we suggest CEMECRYL PRIMER which is liquid admixture to improve bonding, workability and curing of mortar and concrete, then we use the PLASTER PROFILE which is a decorative weatherproofing plaster application for internal and external use on concrete, plaster, mortar and masonry surfaces (multi-colors), then again use CEMECRYL PRIMER to get a protective coat for the plaster profile.

33 Decorative Plaster: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Packaging 5 L or 25 L. Porosity sealer and primer applied directly on the surface. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

34 Decorative Plaster: 2. PLASTER PROFILE is a dry mix of cement and selected aggregates, modified with polymers. Just needs to add water at site to provide a decorative colored finish. Packaging Plaster Profile Colored plaster for outdoor and indoor use. 25 Kg. Package covers 7 smooth surface. 20 colors (BS4800 or RAL colors are available on request). Mixing 25 Kg with 5 L water apply using steel trowel or hopper spray gun and allowed partly, set before finally troweling to a smooth surface, different profiles can be achieved by using mechanical tools. Back to Decorative Plaster Previous

35 Courts Flooring Solution: For More Information Please Click The. Courts Flooring has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the courts flooring after the Surface Preparation is accomplished we suggest CEMECRYL PRIMER which is liquid admixture to improve bonding, workability and curing of mortar and concrete, then we use the CEMELASTIC PATCH which is a sport flooring system. multipurpose acrylic and quartz aggregate compounds, then we use CEMEFLOOR COURT PAINT which is a high quality water base anti-skidding paint for sport flooring based on special type of acrylic emulsion.

36 Courts Flooring Solution: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Packaging 5 L or 25 L. Porosity sealer and primer applied directly on the surface. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

37 Courts Flooring Solution: 2. CEMELASTIC PATCH is an elastic acrylic system, specially formulated for all types of surfaces. It is supplied in the form of a water-based two component, just need to mix at site. UV-rays resistant and nondegradable elastomeric, providing rubberized basecoat to achieve either a professional or intermediate playing surface Packaging CEMELASTIC PATCH Its designed as a basecoat for the Courts Flooring System for levelling and coating. (A) 20 Kg + (B) 50 Kg. Package Covers 15 2 mm thickness. Grey, Green, Red, and Beige (BS4800 or RAL colors are available on request). Apply with trowel and level with a float. Smooth finishing can be achieved with a wooden or foam float. Previous Next

38 Courts Flooring Solution: 3. CEMEFLOOR COURT PAINT is water based acrylic formulation that has been developed for the painting of asphalt, and tarmac tennis courts. Suitable for use on both internal and external applications, has good resistance to UV light. It is a tough, hard wearing paint that possesses wear resistance to medium traffic in parking areas and sport courts applications. Packaging CEMEFLOOR COURT PAINT As a finish coat for indoor and outdoor court ground on concrete or asphalt substrate, and for parking areas, roads and curbstones with medium traffic. 5 Kg or 18 Kg. 1 L Covers 4 m2 per coat. White, Black, Red, and Yellow. Apply using a roller. 2 coats is a must. Back to Courts Flooring Solution Previous

39 Stamped Concrete: For More Information Please Click The. Stamped concrete has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the stamped concrete after the Surface Preparation is accomplished we suggest CEMEHARD 100 which is a dry- Shake cement hardener powder for concrete surfaces, before using the rubber stamps it s a must to use CEMERELEASE AGENT which is a powder used to block the concrete from adhesion with the rubber stamps, then as a final coat use CEMEFLOOR GLAZE which is a transparent polymer sealer, gloss finish, for protection of concrete, and retain the color.

40 Stamped Concrete: 1. CEMEHARD 100 is formulated with special cements, pigments, additives and aggregates designed to be applied on fresh concrete in order to improve its abrasion resistance and provides an anti-dust colored finish in one single application. CEMEHARD 100 Packaging Pavements of garages, parking, shopping malls, schools, hospitals. 25 Kg. 3 Kg covers 1 m2. 20 colors available. spread the powder over the whole surface. Wait until it becomes moist. Do not wet the surface of the concrete during the application. Compact with help of a troweling machine. Next

41 Stamped Concrete: 2. CEMERELEASE AGENT is a powder Release agent used in the Stamped concrete process to avoid adhesive between concrete and rubber stamps. Packaging CEMERELEASE AGENT As a release agent from concrete in the Stamping process, and act as a secondary colorant. 10 Kg. 1 Kg covers 3 m2. Depends on the application. Spread with hand over the troweled concrete and CEMEHARD 100. Previous Next

42 Stamped Concrete: 3. CEMEFLOOR GLAZE is a transparent polymer sealer, derived from methacrylate-based resins. It forms a durable, tough and flexible film with gloss finish for protection of concrete and masonry. It resists weathering, air pollutants, alkaline agents and ultra-violet rays (UV). CEMEFLOOR GLAZE Packaging 5 L or 25 L. Clear acrylic developed to provide hard, glossy, Protective Sealer to beautify and protect regular concrete surface. 1 L Covers microns thickness per smooth surface. None. Apply with brush, roller, or spray, 2 coats recommended. Back to Stamped Concrete Previous

43 Decorative Floors: For More Information Please Click The. Decorative Floors has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products: System 1: In our First system to meet the highest quality of Decorative Floors before applying any product surface preparation must be accomplished then start applying the system products. 1. CEMEFLOOR SF400 Epoxy floor coating system designed for protection of concrete floors. 2. FLAKE CHIPS Small chips designed to give a multi colors. 3. CEMEFLOOR SLC - CLEAR Non-Colored self-leveling epoxy system. System 2

44 Decorative Floors: For More Information Please Click The. Decorative Floors has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products: System 2: In our Second system to meet the highest quality of Decorative Floors before applying any product surface preparation must be accomplished then start applying the system products. 1. CEMEFLOOR METAL FUSION Decorative self-leveling epoxy floor system for protection of concrete floors. System 1 System 3

45 Decorative Floors: For More Information Please Click The. Decorative Floors has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products: System 3: In our Third system to meet the highest quality of Decorative Floors before applying any product surface preparation must be accomplished then start applying the system products. 1. CEMEFLOOR GLITTER Decorative self-leveling epoxy floor system for protection of concrete floors. System 2

46 Decorative Floors: 1. CEMEFLOOR SF400 is a solvent free, two components high build colored system consisting of Epoxy resin and polyamine curing agent. It is designed to provide shameless concrete surface resistance to abrasion and protect against chemical attack. Packaging CEMEFLOOR SF400 High performance epoxy coating with excellent decorative finishing in water tanks, shopping centers, flooring warehouses, floors and walls, and car parking. (A) 4.9 Kg + (B) Kg Package covers micron smooth surface. Standard colors (BS4800 or RAL colors are available on request). Mix (A) with (B) using low speed mixer then apply using short hair roller. Next

47 Decorative Floors: 3. CEMEFLOOR SLC - CLEAR is a clear self-leveling epoxy system, used for apply at multi-thicknesses. non yellowing, non scratch and high bond strength. chemical and abrasion resistance. CEMEFLOOR SLC - CLEAR Typical uses for: 3D Flooring Systems and as Protective Top Coat for indoors. Packaging 5 L. Package covers 5 1 mm smooth surface. None. should be spread on the prepared surface with a notched trowel. Finish off with a spike roller, dense short lambs wool roller, brush, etc. to release entrapped air. Back to Decorative Floors Previous

48 Decorative Floors: 1. CEMEFLOOR METAL FUSION is designed to create elegant and exotic looking seamless floors. Metal Fusion is a two component epoxy formulation consisting of a high performance epoxy resin A blend combined with a curing agent B. Packaging CEMEFLOOR METAL FUSION Ideal for residential and commercial use including, living rooms, kitchens, bathrooms, office spaces, lobby areas etc.. (A) 4.5 Kg + (B) 1.5 Kg Package covers 5 1mm smooth surface. Available in 15 standard metallic colors. Mix (A) + (B) using slow speed mixer Spread the Metal Fusion using notched squeegee and follow behind with a spiked roller. Roll several times with spiked roller. Back to Decorative Floors

49 Decorative Floors: 1. CEMEFLOOR GLITTER is designed to create elegant and glittering looking seamless floors is two component self-leveling consisting of a high performance epoxy resin a blend combined with a curing agent B. Packaging CEMEFLOOR GLITTER Ideal for residential and commercial use including, living rooms, kitchens, bathrooms, retail stores, office spaces, lobby areas etc.. (A) 4.5 Kg + (B) 1.5 Kg. Package covers 5 1mm smooth surface. Available in 5 standard glitter colors. Spread the Glitter using notched squeegee and follow behind with a spiked roller. Roll several times with spiked roller. Back to Decorative Floors

50 Parking & Industrial Floors: For More Information Please Click The. Parking & Industrial Floors are specifically formulated to stand up to the extremes of industrial and manufacturing environments. Ideally suited for manufacturing and assembly areas, forklift aisles and loading docks, Floor systems withstand the constant abuse of heavy loads, impacts, forklift traffic and exposure to liquids and chemical, to meet the highest quality of our products surface preparation must be accomplished. 1. CEMEFLOOR SL 200 Epoxy floor self-leveling high gloss abrasion resist. 2. CEMEFLOOR SF400 Epoxy floor coating system designed for protection of concrete floors 3. CEMEFLOOR SL-ELASTIC Elastic self-leveling epoxy. 4. CEMEFLOOR COLOR COAT Flooring coating interior and exterior, waterproofing, and decorative, and industrial.

51 Parking & Industrial Floors: 1. CEMEFLOOR SL200 is a seamless, Self-Leveling flooring system based on an advanced solvent free epoxy system and selected graded aggregate. The smooth impervious surface finish provides an easily cleaned and hygienic surface with excellent resistance to chemical and mechanical attack. CEMEFLOOR SL200 Ideal for Industrial, stores. Packaging (A) + (B) + (C) = 12 L. Pharmaceutical, cosmetic industries, food factories, and Package covers 6 2mm smooth surface. Standard colors (BS4800 or RAL colors are available on request). Mix (A) + (B) + (C) using slow speed mixer apply into using a notched or flat trowel to a typical thickness of 2mm minimum the surface should be spike rolled to remove the entrapped air, ensure application is continuous. Back to Parking & Industrial

52 Parking & Industrial Floors: 2. CEMEFLOOR SF400 is a solvent free, two components high build colored system consisting of Epoxy resin and polyamine curing agent. It is designed to provide shameless concrete surface resistance to abrasion and protect against chemical attack. Packaging CEMEFLOOR SF400 High performance epoxy coating with excellent decorative finishing in water tanks, shopping centers, flooring warehouses, floors and walls, and car parking. (A) 4.9 Kg + (B) Kg Package covers micron smooth surface. Standard colors (BS4800 or RAL colors are available on request). Mix (A) with (B) using low speed mixer then apply using short hair roller. Back to Parking & Industrial

53 Parking & Industrial Floors: 3. CEMEFLOOR SL-ELASTIC is a self-leveling epoxy system based on special epoxy resin. Vibration and impact resistance due to advanced formula of elastic compounds. While maintaining the hygienic finish with excellent bonding strength and chemical resistance. CEMEFLOOR SL-ELASTIC Ideal for Industrial, Pharmaceutical, cosmetic industries, and vibration areas. Packaging (A) + (B) = 3.6 L. Package covers 3.6 1mm smooth surface. Standard colors (BS4800 or RAL colors are available on request). Applied using a notched or flat trowel to a typical thickness of 2mm minimum the surface should be spike rolled to remove the entrapped air, ensure application is a continuous. Back to Parking & Industrial

54 Parking & Industrial Floors: 4. CEMEFLOOR COLOR COAT is a modified formulated thermoplastic based coating, designed to work as a single component quick curing protective coating for concrete and asphalt floors and walls. Provides a UV resistant waterproofing and abrasion resistant surface. Packaging CEMEFLOOR COLOR COAT Ideal for Industrial, outdoor areas, parking, and roofs. 5 Kg or 20 Kg. 1 Kg covers smooth surface. Standard colors (BS4800 or RAL colors are available on request). Easy to apply by a brush, roller, spray. 2 coats is a must. Back to Parking & Industrial

55 Tiles Adhesive & Grout: For More Information Please Click The. Tiles Adhesive & Grout has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products: System: In our system to meet the highest quality of Tiles Adhesive & Grout before applying any product surface preparation must be done then start applying the system products. 1. Tile-Fix Standard quality tile adhesive General use. 2. Tile-Fix 100 High quality tile adhesive for fixing ceramic tiles on interior and exterior floors and walls surfaces, high durability to water spells and moisture. 3. Tile-Fix 200 Super quality tile adhesive for fixing all types of tiles and vertical stone cladding for interior and exterior uses, waterproof and open time wet, used for pools and wet areas. 4. Tile-Fix 300 Very high quality and durability tile adhesive for special needs, and hardest conditions. 5. ULTRA-GROUT Tile joint filling grout for general use. 6. ULTRA-GROUT UW High quality waterproofing joint filling grout, recommended for immersed tiles and swimming pools use.

56 Tiles Adhesive & Grout: 1. Tile-Fix is a standard quality adhesive for the permanent fixing of ceramic, vitrified, and porcelain tiles Packaging Tile-Fix permanent fixing of ceramic, vitrified, and porcelain tiles. Floors and walls. 20 Kg. Package covers 7 2 mm. White. Mix 20 Kg with 4 L water, should be spread on the substrate to a uniform thickness of 2-3mm, and then combed horizontally with a serrated trowel, and fix tile. Back to Tiles adhesive & Grout

57 Tiles Adhesive & Grout: 2. Tile-Fix 100 is a high quality adhesive for the permanent fixing of ceramic, vitrified, and porcelain tiles. Tile-Fix 100 Packaging permanent fixing of ceramic, vitrified, and porcelain tiles. Indoor and outdoor, floors and walls. 20 Kg. Package covers 7 2 mm. White. Mix 20 Kg with 4 L water, should be spread on the substrate to a uniform thickness of 2-3mm, and then combed horizontally with a serrated trowel. Back to Tiles adhesive & Grout

58 Tiles Adhesive & Grout: 3. Tile-Fix 200 is a super quality adhesive for the permanent fixing of glass mosaic tiles and vertical stone cladding. Tile-Fix 200 Packaging All types tiles and vertical stone cladding, wet areas and swimming pool. 20 Kg. Package covers 7 2 mm. White. Mix 20 Kg with 4 L water, should be spread on the substrate to a uniform thickness of 2-3mm, and then combed horizontally with a serrated trowel. Back to Tiles adhesive & Grout

59 Tiles Adhesive & Grout: 4. Tile-Fix 300 is a special quality adhesive for the permanent fixing of tiles in damp and totally submerged conditions, for heavy tiles and stone, for special harsh environments. Tile-Fix 300 Packaging Swimming pools, Fountains, Bathroom floors, Splash zones, and heavy stones. 20 Kg. Package covers 7 2 mm. White. Mix 20 Kg with 4 L water, should be spread on the substrate to a uniform thickness of 2-3mm, and then combed horizontally with a serrated trowel. Back to Tiles adhesive & Grout

60 Tiles Adhesive & Grout: 5. ULTRA-GROUT is a polymer based cementitious tile joint filler used in filling gaps and levels itself to give hard wearing, non dusting, anti-fungus tile joints. Packaging ULTRA-GROUT It provides smooth water resistant hard wearing tile joints. 5 Kg or 20 Kg. Package 5 Kg covers 15 2 mm joint width. 14. Mix 5 Kg with 1 L water apply the mix to the tile joints with a steel or plastic trowel, then smoothen with a sponge. Back to Tiles adhesive & Grout

61 Tiles Adhesive & Grout: 6. ULTRA-GROUT UW is a two component tile joint filling grout, powder and resin to be mixed on site, for exterior or under water applications, such as kitchens bathrooms and swimming pools, anti-fungus tile joints. ULTRA-GROUT UW Packaging (A) 5 Kg + (B) 1 L. It provides smooth water resistant hard wearing tile joints for under water and exterior use. Package covers 15 2 mm joint width. 14. Mix (A) 5 Kg with (B) 1 L using a slow speed mixer then apply to the joint using a steel trowel. Back to Tiles adhesive & Grout

62 Swimming Pool Waterproofing: For More Information Please Click The. Swimming pool Waterproofing has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the Swimming pool waterproofing after the Surface Preparation is accomplished we suggest to waterproof the tanks from inside and outside: Inside Swimming Pool: 1. CEMECRYL PRIMER is liquid admixture to improve bonding, workability and curing of mortar and concrete. 2. CEMESEAL FLEX is a waterproofing coat for water wells, and swimming pools. 3. Tile-Fix 300 Very high quality and durability tile adhesive for special needs. 4. ULTRA-GROUT UW High quality waterproofing joint filling grout, recommended for immersed tiles and swimming pools use Outside Swimming Pool: 5. BITUPRIME EL-10 Cold rubberized bitumen emulsion for underground foundations and walls waterproofing.

63 Swimming Pool Waterproofing: 1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity. CEMECRYL PRIMER Packaging 5 L 25 L. Porosity sealer and primer applied directly on the surface. 1 L Covers micron smooth surface. None. Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry and once it has been completely absorbed in the support, depending on porosity, apply the mortar or concrete, apply next material within 10 hours after priming. Next

64 Swimming Pool Waterproofing: 2. CEMESEAL FLEX is a cementitious acrylic two-component product that provides a non-toxic, flexible and waterproof coating with very high adhesion on those common substrates in construction such as concrete and masonry. CEMESEAL FLEX Packaging (A) 18 Kg + (B) 5 L. Waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools. Package Covers micron thickness. Grey (Concrete Color). Mix with electrical mixer then apply it using a short, stiff bristle brush or roller. Previous Next

65 Swimming Pool Waterproofing: 3. Tile-Fix 300 is a special quality adhesive for the permanent fixing of tiles in damp and totally submerged conditions, for heavy tiles and stone, for special harsh environments. Tile-Fix 300 Swimming pools, Fountains, Bathroom floors, Splash zones, and heavy stones. Packaging 20 Kg. Package covers 7 2 mm. White. Mix 20 Kg with 4 L water, should be spread on the substrate to a uniform thickness of 2-3mm, and then combed horizontally with a serrated trowel. Previous Next

66 Swimming Pool Waterproofing: 4. ULTRA-GROUT UW is a two component tile joint filling grout, powder and resin to be mixed on site, for exterior or under water applications, such as kitchens bathrooms and swimming pools, anti-fungus tile joints. ULTRA-GROUT UW Packaging (A) 5 Kg + (B) 1 L. It provides smooth water resistant hard wearing tile joints for under water and exterior use. Package covers 15 2 mm joint width. 14. Mix (A) 5 Kg with (B) 1 L using a slow speed mixer then apply to the joint using a steel trowel. Previous Next

67 Swimming Pool Waterproofing: 5. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing. BITUPRIME EL-10 Packaging 5 L or 18 L or 200 L. 1 L Covers 3 m2. s from building foundations to bridge abutments, retaining walls, flower boxes, box gutters or any other area where water must be kept in or out. Brown. Mix with electric mixer for minutes then apply easily and inexpensively by unskilled personnel. No special equipment is required as application is by normal brushes, or rollers. Back to Swimming pool Previous

68 Basement & Foundation Waterproofing: For More Information Please Click The Product Name. Basement & Foundation Waterproofing has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products : System: In our system to meet the highest quality of Basement & Foundation Waterproofing before applying any product surface preparation must be accomplished then start applying the system products. 1. BITUPRIME Cold rubberized bitumen emulsion for underground foundations waterproofing. 2. BITUFLEX EL-5 Cold rubberized bitumen emulsion for underground foundations waterproofing 5% rubberized. 3. BITUFLEX EL-10 Cold rubberized bitumen emulsion for underground foundations waterproofing 10% rubberized

69 Basement & Foundation Waterproofing: 1. BITUPRIME a cold rubberized bitumen emulsion, easily applied for waterproofing of underground foundation. BITUPRIME Packaging 5 L or 18 L or 200 L. 1 L Covers 3 m2. s from building foundations to bridge abutments, retaining walls, flower boxes, box gutters or any other area where water must be kept in or out. Brown. Mix with electric mixer for minutes then apply easily and inexpensively by unskilled personnel. No special equipment is required as application is by normal brushes, or rollers. Back to Basement & Foundations

70 Basement & Foundation Waterproofing: 2. BITUPRIME EL-5 is a highly effective and cost efficient method of waterproofing brick, concrete. It is a rubber bitumen emulsion which when dries form a tough, elastic membrane. BITUPRIME EL-5 Packaging 5 L or 18 L or 200 L. 1 L Covers 3 m2. s from building foundations to bridge abutments, retaining walls, flower boxes, box gutters or any other area where water must be kept in or out. Brown. Mix with electric mixer for minutes then apply easily and inexpensively by unskilled personnel. No special equipment is required as application is by normal brushes, or rollers. Back to Basement & Foundations

71 Basement & Foundation Waterproofing: 3. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing. BITUPRIME EL-10 Packaging 5 L or 18 L or 200 L. 1 L Covers 3 m2. s from building foundations to bridge abutments, retaining walls, flower boxes, box gutters or any other area where water must be kept in or out. Brown. Mix with electric mixer for minutes then apply easily and inexpensively by unskilled personnel. No special equipment is required as application is by normal brushes, or rollers. Back to Basement & Foundations

72 Stone Facades Waterproofing: For More Information Please Click The. Stone Facades Waterproofing has many system solutions depends on the location, area, weather conditions, and site conditions. We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products: System: In our system to meet the highest quality of Stone Facades Waterproofing before applying any product surface preparation must be done then start applying the system products. 1. ULTRA-HOLD High quality waterproofing joint filler for limestone joints. 2. ACRY-SEAL WB High quality water-base proof for limestone. 3. SILO-SEAL WB Water base water-repellent for stone protection colorless and ready to use. 4. SILO-SEAL SB Solvent base water-repellent for stone protection colorless and ready to use

73 Stone Facades Waterproofing: 1. ULTRA-HOLD is a dry mix mortar, highly modified to work as a joint filler at stone facades. Its waterproofing and non-shrink. ULTRA-HOLD To fill limestone joints. Packaging 25 Kg. Depends on joint width and depth. White, Yellow, and Grey (BS4800 or RAL colors are available on request). Mix 25 Kg with 5 L of water then apply the mix to the joint with a steel trowel and a sponge. Back to Stone Facades

74 Stone Facades Waterproofing: 2. ACRY-SEAL WB is a non-staining water-repellent liquid composed of milky siloxane silane resin specially formulated for limestone substrate, plaster or similar, low-fired clay and gypsum plasters. ACRY-SEAL WB Invisible protection for limestone façades and exterior plasters. Packaging 25 L. Package covers 100 m2. None. Applied by brush, roller, or low pressure spray. Back to Stone Facades

75 Stone Facades Waterproofing: 3. SILO-SEAL WB is a water-repellent liquid composed of invisible water-based silicon resin specially formulated for limestone substrates or similar, low-fired clay and gypsum plasters. SILO-SEAL WB Invisible protection for limestone façades and exterior plasters. Packaging 5 L or 25 L. Package covers 20 m2. Or Package covers 100 m2. None. Applied by brush, roller, or low pressure spray. Back to Stone Facades

76 Stone Facades Waterproofing: 4. SILO-SEAL SB is a solvent base water-repellent, for protection and waterproofing of stone or plaster facades. SILO-SEAL SB Invisible protection for limestone façades and interior plasters. Packaging 5 L or 25 L. Package covers 20 m2. Or Package covers 100 m2. None. Applied by brush or low pressure spray. Back to Stone Facades